Tuesday 29 June 2021

apmsleep - Unix, Linux Command

LPI Exam Prep, LPI Tutorial and Material, LPI Certification, LPI Guides, LPI Preparation, LPI Learning, LPI Career

NAME

apmsleep - go into suspend or standby mode and wake-up later

SYNOPSIS

apmsleep [-sSnwhVd] [--suspend] [--standby] [--noapm] [--wait] [--precise] [--help] [--version] [--debug] [+]hh:mm

More Info: 010-160: LPI Linux Essentials (Linux Essentials 010)

DESCRIPTION

Some computers, especially laptops, can wake-up from a low-power suspend to DRAM mode using the Real-time-clock (RTC) chip. Apmsleep can be used to set the alarm time in the RTC and to go into suspend or standby mode. An interrupt from the RTC causes the computer to wake-up. The program detects this event, by waiting for a leap in the kernel time and terminates successfully. If no time leap occurs within one minute, or something goes wrong, the exit value will be non-zero.

The wake-up time can be specified in two formats:

+hh:mm specifies a relative offset to the current time. The computer will suspend for exactly hh hours and mm minutes plus a few seconds to wake up. On some laptops, the timing is not completely accurate so it may be a few minutes (or more?) late.

hh:mm specifies absolute local time in 24-hour format. The time stored in the RTC is not important. You may change the time zone used, with the TZ environment variable as usual. Daylight saving time is not obeyed in this version, but might be in a future release. WARNING: Do not close cover of laptop after suspending the laptop with apmsleep. Most laptops overheat when running with closed cover.

Energy conservation with APM is little for a desktop. Turning of the screen will save 1/2, going into standby with drives turned off will save another 1/6th of the current.

Tag Description 
-V, --version  
  Print the apmsleep program version and exit immediately.
-s, --suspend   
  Put the machine into suspend mode if possible (default). On my laptop, suspend mode turns off everything except the memory. 
-S, --standby   
  Put the machine into standby mode if possible. On my laptop, standby mode turns off screen, hard disk, and CPU. 
-w, --wait  Wait indefinitely for the time leap. 
-p, --precise   
  Wait for alarm time to match actual time. Do not wait for time leap. This might be useful even without APM. 
-n, --noapm   
  Do not call apm bios to suspend computer, just set the alarm clock and wait for time leap indefinitely. 
-d, --debug  
  Print some information about what is going on.

REQUIRED SYSTEM CONFIGURATION

Tag Description 
Kernel The special character device /dev/rtc must exist and the kernel needs to be compiled with APM and RTC support.
BIOS  The computer must have the ’suspend to RAM’ feature enabled in the BIOS; ’suspend to Disk’ will not work, because the computer is turned off completely. You do not need to enable the ALARM timer, it will be activated by apmsleep. On some boards, you can configure which interrupts can be used to awake from suspend mode. If you have such a board, you might want to make sure that keyboard (IRQ 1) and RTC (IRQ 8) are among those interrupts. If your computer does not wake up, try to enable ’modem ring’ in the BIOS, even if you do not have a modem.
Privileges  
  The program must be run as root or have the SUID attribute set (see chmod(1)).

BUGS

Apmsleep cannot detect which event terminated the suspension. Possible events are: keyboard or mouse activity, modem ring, alarm from RTC, any other interrupt. Sometimes, the time leap is not detected properly (causing a wrong exit value).

Should use APM BIOS calls to set alarm clock (not yet supported by kernel).

This program was tested on a Winbook XL laptop (Pentium) only. It may not function on your hardware.

Source: tutorialspoint.com

Related Posts

0 comments:

Post a Comment